Click to learn more

Maryville, TN Job Opportunities

GUN FINDER

collection-pistol.jpg

revolvers-icon.jpg

long-guns-icon.jpg

specialtyservice.png

merchandise.jpg

MERCHANDISE

FAQs

CATALOGS

INVENTORS

OWNER'S MANUALS

PRODUCT REGISTRATION

REBATES

GUNSMARTS

SAFETY

AMERICAN GUARDIANS

THE S&W BENCH™

NEWS

OUR STORY

location-dot-solid.svg

Dealer Locator

Since 1852 we’ve been an industry leading manufacturer of pistols, revolvers, rifles, and shooting accessories. We continue to bring innovative firearms to market that meet the needs of every shooter and deliver on exceptional quality with a brand you’ve learned to trust.

All consumer products display on /products/. It is necessary to put items in this category for proper data compliance. A product may be a part of both Consumer and LE/Military, or only one. If a product is not a part of one of these categories, it will not show on the frontend website.

Consumer

sw-logo-bm.png

sw-logo-txt.png

Smith & Wesson

Smith & Wesson (Consumer)

Browse all Smith & Wesson recalls below.

Smith & Wesson - Consumer Recalls

IMPORTANT! M&amp;P15-22 CONSUMER SAFETY ALERT AND INSPECTION PROCEDURE DESCRIPTION - Please Read This If You Have A M&amp;P15-22 Rimfire Firearm. PRODUCT AFFECTED: ALL models of M&amp;P15-22 rifles and pistols manufactured before February 1, 2019. STOP USING YOUR M&amp;P15-22 UNTIL IT HAS BEEN INSPECTED AND YOUR BOLT REPLACED (IF NECESSARY). Smith &amp; Wesson has identified two M&amp;P15-22 firearms from recent production on which the breech face counter bore depth was not within manufacturing specification. In those firearms, the lack of depth may allow the bolt, upon closing, to crush the rim of the case, causing the round to fire, cycling the bolt, and potentially resulting in multiple discharges without depressing the trigger. This issue can occur in the following two scenarios: 1)&nbsp;With a loaded magazine in the firearm and the bolt locked to the rear, depressing the bolt release to allow the bolt to drop freely may ignite the round as the bolt closes without engaging the trigger and with the safety selector in either the safe or the fire position, and may also result in multiple discharges. 2)&nbsp;With a loaded magazine in the firearm, bolt in the closed position and a round in the chamber and the safety selector in the fire position, depressing the trigger will cause the round to fire normally, however as the bolt cycles, the next round may be ignited by the bolt crushing the rim of the case as it closes, causing multiple discharges. We believe that these are isolated incidents, however, any unintended discharge of a firearm has the potential to cause injury. Therefore, we have developed this inspection procedure to ensure that all products in the field are safe to use. We are asking customers to perform the following procedure and to refrain from using their M&amp;P15-22 until the bolt has been inspected and replaced as necessary.DESCRIPTION OF THE PRODUCT INVOLVED: The out of specification condition has been found only in bolts that were recently manufactured. While our investigation suggests that the incidents are isolated, we have established this inspection procedure as a precautionary matter to ensure that all M&amp;P15-22 firearms in service meet our design specifications. We are asking consumers of all M&amp;P15-22 firearms manufactured before February 1, 2019 to inspect their bolt for this condition. REMEDY/ACTION TO BE TAKEN: The bolt from your M&amp;P15-22 must be inspected to determine whether it exhibits the condition identified in this notice. To determine whether your firearm is affected by this condition, please inspect your firearm by following the inspection instructions provided here. <a href="https://assets.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt2ba9e342d99554a1/63d3f9d5b369f5745550bd6c/MP1522_Alert_030619.pdf" target="_self">DOWNLOAD INSTRUCTION MANUAL</a>&nbsp;|&nbsp;<a href="https://www.youtube.com/watch?v=UJO0gJRmc_c&feature=youtu.be" target="_self">VIEW INSPECTION VIDEO</a><figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltef7e7390d7deb985/638e57876e37161066eed554/M&P1522_Alert_2019_PG1.jpg" alt="Instruction manual" /></figure><figure style="float: none;width: auto;text-align: none;"><figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt3444cd9e6915472c/638e57ee4c3a2b1b59fa23b8/M&P1522_Alert_2019_PG2.jpg" alt="Instruction manual" /></figure></figure><figure style="float: none;width: auto;text-align: none;"><figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltf646dc24495a7a0c/638e5809a8ba0e5eb857defd/M&P1522_Alert_2019_PG3.jpg" alt="Instruction manual" /></figure></figure><figure style="float: none;width: 285px;text-align: none;"><figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt2cc36e5e4e28b715/638e5820196547511e1c38de/M&P1522_Alert_2019_PG4.jpg" alt="Instruction manual" height="367" style="height: 367;" /></figure></figure><div><a href="https://assets.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blta0e99385fee74b23/63d3fb231abe0e27cb1f2a1b/MP1522_Alert_FAQ_030719.pdf" target="_self">CLICK HERE FOR FAQ FACT SHEET&nbsp;- Questions and Answers Re: M&amp;P15-22 Safety Alert!</a></div> If you are uncomfortable in conducting the bolt inspection outlined here, or are unsure whether the condition described in this notice applies to your bolt, please send your bolt to Smith &amp; Wesson for inspection and replacement if necessary.If you want Smith &amp; Wesson to perform the inspection, send your bolt to Smith &amp; Wesson for free inspection and replacement (if necessary). If you want to perform the bolt inspection yourself, contact us for the free M&amp;P15-22 BOLT INSPECTION GAUGE Part Number: 3012155 or place an&nbsp;<div><a href="https://store.smith-wesson.com/m-p-15-22-bolt-inspection-gauge" target="_self">ORDER ONLINE</a></div>&nbsp;to receive inspection gauge.If the bolt from your firearm is affected by the condition outlined in this notice, please send the bolt to Smith &amp; Wesson. If necessary, your bolt will be replaced at no cost to you. Your bolt will be returned as quickly and efficiently as possible. All shipping and replacement costs will be covered by Smith &amp; Wesson.FOR OWNERS OUTSIDE THE UNITED STATES: For M&amp;P15-22 owners outside the United States, see our list of&nbsp;<div><a href="https://www.smith-wesson.com/customer-service/warranty-stations" target="_self">Authorized Warranty Centers</a></div>&nbsp;that will inspect and replace your bolt as necessary.

M&P15-22 CONSUMER SAFETY ALERT

IMPORTANT CONSUMER SAFETY ALERT and INSPECTION PROCEDURE August 22, 2013 PRODUCT:&nbsp;&nbsp;ALL&nbsp;M&amp;P Shield™ firearms manufactured before August 19, 2013. DESCRIPTION OF THE HAZARD:&nbsp;Smith &amp; Wesson has identified a condition where the trigger bar pin could damage the lower trigger in certain M&amp;P Shields in a way that may affect the functionality of the drop safety feature of the firearm, potentially allowing the pistol to discharge if it is dropped.Any unintended discharge of a firearm has the potential to cause injury, and we ask that you&nbsp;STOP USING YOUR PISTOL IMMEDIATELY UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED. DESCRIPTION OF THE PRODUCT INVOLVED:&nbsp;&nbsp;This Safety Alert applies to all M&amp;P Shield pistols manufactured before August 19, 2013. We believe this condition is largely limited to recently manufactured M&amp;P Shield pistols.&nbsp; However, out of an abundance of caution, we are asking&nbsp;all&nbsp;consumers of all M&amp;P Shields manufactured before August 19, 2013, to immediately inspect their pistols for this condition. INSPECTING YOUR PISTOL Your firearm must be inspected to determine whether it exhibits the condition identified in this notice.&nbsp;&nbsp;To determine whether your firearm is affected by this condition, please inspect your firearm as follows: 1.&nbsp;Follow the procedures in your Safety &amp; Instruction Manual to&nbsp;ENSURE THE FIREARM IS UNLOADED; ENSURE THAT THE MUZZLE IS POINTED IN A SAFE DIRECTION; THE SLIDE IS LOCKED BACK; AND THE MANUAL SAFETY IS ENGAGED. 2.&nbsp;Hold your pistol sideways with the muzzle pointed to the left.&nbsp; Look at the trigger.&nbsp; Note that the trigger is actually two pieces, with a pin in the middle that connects the two halves (Figure 1).<figure style="float: none;width: auto;text-align: none;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt018a70ec5d388954/638e5a36a8ba0e5eb857df0b/mpshield-safetyalert-001.jpg" alt="Trigger of gun"/></figure>3.&nbsp;Look at Figure 2.&nbsp; Without touching the trigger, identify the plastic tab circled in red in Figure 2.<figure style="float: none;width: auto;text-align: none;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt1ac7a591597ff3fc/638e5a578f635b33e8e12d1b/mpshield-safetyalert-002.jpg" alt="Trigger of gun"/></figure>4.&nbsp;Slowly pull the trigger.&nbsp; The plastic tab encircled in Figure 2 should disappear into the upper trigger section (Figure 3).<figure style="float: none;width: auto;text-align: none;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltf534fe5c837d6c22/638e5a7703ce2a511dcf8633/mpshield-safetyalert-003.jpg" alt="Trigger of gun"/></figure>5.&nbsp;Slowly release the trigger.&nbsp; The tab should reappear as shown in Figure 2 completely on its own. 6.&nbsp;Repeat steps 4 and 5 several times.&nbsp; If the small tab as shown in Figure 2 reappears each time, your pistol does not require repair. 7.&nbsp;If the small tab does not consistently reappear as shown in Figure 2,&nbsp;YOUR PISTOL MUST BE RETURNED FOR SERVICE. If you are uncomfortable conducting the inspection outlined above or are unsure whether the condition described in this notice applies to your firearm, please take your firearm to your local M&amp;P Certified Armorer or send your firearm to Smith &amp; Wesson for inspection.&nbsp;&nbsp;M&amp;P Armorers can be found on the&nbsp;<a href="http://smith-wesson.com/" target="_self">smith-wesson.com</a>&nbsp;website by using the Dealer Locator feature. If after inspection it is determined that the condition outlined in this safety alert exists, the firearm must be sent to Smith &amp; Wesson for repair. REMEDY/ACTION TO BE TAKEN: STOP USING YOUR FIREARM UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED. Your firearm must be inspected to determine whether it exhibits the condition identified in this notice.&nbsp;&nbsp;To determine whether your firearm is affected by this condition, please inspect your firearm by following the inspection instructions above. If your firearm is affected by the condition outlined in this notice, please send your pistol to Smith &amp; Wesson.&nbsp;&nbsp;Your firearm will be inspected, and if necessary, repaired at no cost to you. Your firearm will be returned within 5 to 7 business days.&nbsp; All shipping and repair costs will be covered by Smith &amp; Wesson. Outside the United States, click&nbsp;<a href="https://www.smith-wesson.com/customer-service/warranty-stations" target="_self">HERE</a>&nbsp;for a list of Authorized Warranty Centers that will repair your pistol. CONSUMER CONTACT:&nbsp;Please contact Smith &amp; Wesson directly at 877-899-6259

M&P SHIELD CONSUMER SAFETY ALERT

<h2>IMPORTANT SAFETY RECALL NOTICE - SEPTEMBER 16, 2016</h2><h2>T/C COMPASS RIFLES &nbsp;</h2>DESCRIPTION OF&nbsp;THE HAZARD:&nbsp;Thompson/Center has identified a condition that may exist in some Compass rifles. &nbsp;We have determined that there may be some instances, depending on the height and position of the rifle and other factors, where a chambered round may fire if the firearm is dropped with the safety in the fire position.&nbsp; Safety is paramount to us, so we are taking this measure to further enhance performance and to meet our customer expectations, with the goal of reducing the chance of an accidental discharge should the rifle be dropped. DESCRIPTION OF&nbsp;THE PRODUCT&nbsp;INVOLVED:&nbsp;This recall applies to all Compass rifles manufactured by Thompson/ Center prior to September 16, 2016. REMEDY/ACTION TO&nbsp;BE TAKEN:&nbsp;STOP USING YOUR RIFLE.Any unintended discharge of a firearm has the potential to cause injury and we are asking all Compass owners to immediately stop using their rifles until corrective action can be taken.&nbsp; To remedy this condition, your rifle will be inspected and if necessary repaired at no cost to you. Your firearm will be returned as quickly and efficiently as possible. All shipping and repair costs will be covered by Thompson/Center Arms.To facilitate this repair, please contact Thompson/Center at the number below to arrange for the return of your rifle.&nbsp; You will promptly receive a shipping return label with instructions on the return of your rifle.&nbsp; While you are awaiting the shipping instructions, remember that the rifle should always be stored unloaded and with the safety in the SAFE – LOAD/UNLOAD position as shown below:&nbsp;<figure style="float: none;width: auto;text-align: none;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltd0dc39a4f3c56f9a/638e5c42b6458e671e0c00ee/compass-recall-001.png" alt=" LOAD/UNLOAD position shown "/></figure><figure style="float: none;width: auto;text-align: none;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt30e400e911ce99c2/638e5c58e133455e0fe8d7ac/compass-recall-002.png" alt=" LOAD/UNLOAD position shown "/></figure>See the Owner’s Manual for complete storage instructions.VERIFICATION OF CORRECTIVE ACTION:&nbsp;When your rifle is returned, you should note a punch dot on the receiver. See the photograph below. The mark is only visible with the bolt removed. This punch dot is confirmation that your rifle has been inspected and the hazard has been corrected.<figure style="float: none;width: auto;text-align: none;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt99c06fa2f310844c/638e5c772f42a15313a04f09/compass-recall-003.png" alt="A punch dot on the receiver"/></figure><figure style="float: none;width: auto;text-align: none;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltc57b33f88ba24b41/638e5c8d744e571054aa896f/compass-recall-004.png" alt="A red star on the label"/></figure>When your rifle is returned, you should also note a red star on the label on the outside of your box. See the photograph above. This mark is further confirmation that your rifle has been inspected and the hazard has been corrected.CONSUMER CONTACT:&nbsp;To arrange for the inspection and repair of your Compass rifle, in the United States, please call us at (855) 512-5935 or complete the safety recall form using the link below to receive a FedEx pre-paid label and shipping instructions. Outside the United States, click&nbsp;<a href="http://www.smith-wesson.com/customer-service/warranty-stations" target="_self">HERE</a>&nbsp;for a list of Authorized Warranty Stations that will repair your rifle.IF YOU HAVE ANY QUESTIONS ABOUT THIS RECALL, PLEASE CONTACT THOMPSON/CENTER AT&nbsp;855-899-6259

TCA COMPASS® RIFLES SAFETY RECALL MANUFACTURED PRIOR TO 9.16.16

<h5>Product Under Safety Recall Notice</h5>Bolt from Smith &amp; Wesson's i-Bolt rifle.&nbsp;<h5>Description of the Hazard</h5>Smith &amp; Wesson has identified a condition that may exist with the bolt supplied with some rifles that would allow the striker to become disengaged from its locking tabs during cycling of the bolt, allowing the rifle to fire without the trigger being pulled. &nbsp;In the interest of consumer safety, we are initiating this recall to allow for the prompt inspection and, if necessary, the repair and replacement of each bolt.&nbsp;Description of the Product InvolvedThis recall applies to the bolts of all i-Bolt rifles manufactured by Smith &amp; Wesson prior to December 1, 2008.&nbsp;<h5>Action to be Taken</h5>STOP USING YOUR RIFLE.Any unintended discharge of a firearm has the potential for causing injury, and we ask that you stop using your rifle until we have an opportunity to inspect the bolt to make certain that there is no condition which will allow the striker to disengage.To facilitate the inspection and repair, if necessary, of your rifle bolt, please contact Smith &amp; Wessons customer service department to receive instructions and a call tag for the return of your bolt to Smith &amp; Wesson.When you return your bolt to Smith &amp; Wesson, be sure to attach the completed information card received from Smith &amp; Wesson, so that your bolt can be inspected and repaired, and returned to you as quickly and efficiently as possible.<h5>Verification of Corrective Action</h5>When your rifle bolt is returned, you should note a punch dot on the handle of the bolt.&nbsp; See the photograph below.&nbsp; This punch dot is confirmation that your bolt has been inspected and is safe to use.<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt49fdc79f00a8884c/638e593c50209905f8d4f413/Grey_Bolt_1_sm.jpg" alt="A punch dot on the handle of the bolt" /></figure> <h5>Consumer Contact</h5>To receive a FedEx pre-paid billable stamp and shipping instructions to arrange for the inspection and repair, if necessary, of your bolt, contact Smith &amp; Wesson directly at 1-800-331-0852 or email us at&nbsp;<a href="mailto:qa@smith-wesson.com" target="_self">qa@smith-wesson.com</a>.&nbsp;

I-BOLT RIFLE BOLT SAFETY RECALL

This safety recall notice applies to the&nbsp;limited edition model 329 revolver manufactured at the Smith &amp; Wesson performance center. This safety recall notice applies to 270 revolvers manufactured at the performance center bearing serial numbers - ranging from&nbsp;BVA0004 to BVA0210 and DEW0001 to DEW0099.It has been determined that damage to the frame may have occurred during assembly of the single piece barrel. As a result, there exists the possibility that the revolver may rupture during firing, causing a failure of the firearm and creating a risk of personal injury.You should immediately stop using the revolver and return it to Smith &amp; Wesson. Upon return Smith &amp; Wesson will issue a refund or a credit towards the purchase of a replacement firearm.To determine if your revolver is subject to this safety recall notice, please check the serial number. The serial number is displayed on the frame of the revolver and is visible with the cylinder open.&nbsp;See the diagram below:<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt9166083329fe8c9d/638e5b36a6b3fb1083c3d5c8/329recall.jpg" alt="Serial number displayed on the frame of the revolver with the cylinder open" /></figure>Please note that this safety recall notice does not apply to the model 329 PD. The model 329 PD is designed with a two-piece barrel. Because of this and other design, manufacture and assembly differences that exist between the model 329 PD and the limited edition model 329 manufactured at the performance center, the safety and performance concerns that led to this recall do not affect the model 329 PD.&nbsp;You should return your revolver only if it is a model 329 with a serial number in the range specified above.Please contact Smith &amp; Wesson directly at 1-800-331-0852 to arrange for the return of your firearm.

PERFORMANCE CENTER MODEL 329 SAFETY RECALL

IMPORTANT SAFETY RECALL NOTICE FOR SMITH &amp; WESSON®&nbsp;M&amp;P®12 SHOTGUNS MANUFACTURED PRIOR TO OCTOBER 15, 2021Smith &amp; Wesson has received two field reports of cracked barrels involving the M&amp;P12 Shotgun. To ensure that all of our Shotguns meet Smith &amp; Wesson’s high standards for quality, we are implementing this Safety Recall of all Shotguns manufactured prior to October 15, 2021, to ensure there are no surface anomalies or conditions that might adversely affect the safety, function or performance of these Shotguns. Please STOP USING your M&amp;P12 Shotgun until it has been inspected and, if necessary, repaired by Smith &amp; Wesson. PRODUCT AFFECTED:This notice applies to M&amp;P12 Shotguns manufactured prior to October 15, 2021. To determine whether your M&amp;P12 Shotgun is affected, check the label on the box to determine the date of manufacture (see image below). If the manufacture date is prior to October 15, 2021, your shotgun is subject to this Recall and should be returned to Smith &amp; Wesson for inspection. If you are unsure of your date of manufacture, input your serial number below, or call 833-957-3476. HOW TO LOCATE YOUR SERIAL NUMBER AND DATE OF MANUFACTURE<figure style = "float: none;width: 715px;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltafb490733d3916a0/638e55cfb6458e671e0c00d8/serial-number-location-mp12-label-final.jpg" alt="Serial number and date of manufacture on a label" style="height: auto;" /></figure>REMEDY/ACTION TO BE TAKEN: To determine whether your Shotgun was manufactured prior to October 15, 2021,&nbsp;please input your serial number below. If your Shotgun was manufactured prior to October 15, 2021, please call 833-957-3476 to obtain a pre-paid return label, to arrange for the return of your Shotgun to Smith &amp; Wesson for inspection. After inspection, if the barrel from your Shotgun is affected, it will be replaced at no cost to you. Your Shotgun will be returned as quickly and efficiently as possible. All shipping and replacement costs will be covered by Smith &amp; Wesson. FOR DEALERS/DISTRIBUTORS/RETAILERS: If you have affected Shotguns in your inventory, please call 833-957-3476 and we will coordinate the return of the affected firearms. The Shotguns will be expedited to our facility, repaired, and returned to you ASAP.For those Shotguns which you have already sold, we ask that you provide us with the names, addresses, telephone numbers and e-mails of customers to whom you have sold them. Please send this information to us electronically at&nbsp;<a href="mailto:MPshotgunrecall@smith-wesson.com" target="_self">MPshotgunrecall@smith-wesson.com</a>. If you do not have the capability to return the form electronically, please call 833-957-3476. This information is vital to ensure that notice of the recall is given to all affected purchasers. Once we receive this information from you, we will immediately arrange to provide notice of the recall directly to your customers.

SAFETY RECALL NOTICE FOR M&P®12 SHOTGUNS

<h3>VERIFY YOUR SERIAL NUMBER IS AFFECTED BELOW BEFORE CONTINUING</h3>*The Walther PPS M1 models are NOT affected by the recall.&nbsp; If you have a PPS M1 you do NOT need to send it in for the upgrade.Important Safety Recall – November 2018 Walther PPS M2 PistolsWalther Arms, Inc. has recently discovered a potential safety issue with certain PPS M2 pistols. &nbsp;Walther is voluntarily initiating a recall to protect the safety of its customers because under certain conditions it is possible that some of these pistols may fire when dropped.Please do not load or fire your Walther PPS M2 pistol and contact us immediately to arrange to have your pistol upgraded free of charge.If your pistol has already been upgraded, there will be&nbsp;a dot milled onto the back side of the magazine well opening.&nbsp;NOTE:&nbsp;If the serial number of your PPS M2 is not within the range listed it will NOT have the mark shown above.&nbsp;<figure style = "float: none;width: 330px;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt25b2661d15b72065/638e5df0156a5e1078f0eb58/Recall-Image-1-50.jpg" alt="The back side of the magazine well opening" style="height: auto;" /></figure><figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt29038c7b48172d63/638e5e00bc3535195feb1837/Recall-Image-2-50.jpg" alt="Before after pictures of the back side of the magazine well opening. " /></figure>The upgrade will be performed at no charge to you.&nbsp; For free shipping, please enter your information&nbsp;<div><a href="https://waltherarms.wufoo.com/forms/w1rujkj505x5abg/" target="_self">here</a>,&nbsp;and&nbsp;complete the online form. NOT ALL PPS M2 MODELS ARE AFFECTED. Be sure to VERIFY that your serial number is affected by the recall before shipping your gun back for the recall.&nbsp;After completion of the form a confirmation&nbsp;email will be sent including shipping information.</div>Please note:&nbsp; The Serial Number is located on the right side of the pistol (circled in red below)<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt86686a87cf98447b/638e5e28b660b4108abd04cc/Walther_PPS-M2-SN-Image.jpg" alt="Serial Number on a Walther PPS M2 pistol" /></figure>This recall applies to Walther PPS M2 pistols which have a Serial Number ranging from&nbsp;AN3020 to AU7502ONLY SERIAL NUMBERS BELOW ARE AFFECTED BY THE RECALL.AN3020 through AN9999AO0001 through AO9999AP0001 through AP9999AQ0001 through&nbsp;AQ9999AR0001 through AR9999AS0001 through AS9999AT0001 through AT9999AU0001 through AU7502*If you are unsure if your Serial Number is involved in the recall, please email:&nbsp;<a href="mailto:PPSM2Recall@WaltherArms.com" target="_self">PPSM2Recall@WaltherArms.com</a>If your PPS M2 is AN3019 or earlier your handgun is not included in the recall.If your PPS M2 is AU7503 or later your handgun is not included in the recall.&nbsp;Serial numbers that start with AY, AX, AZ, BA, BB are not affected.SUBMIT YOUR INFORMATION HERE – PPS M2 RECALL&nbsp;Please check this website and all safety notices on a regular basis for current information about your firearms.&nbsp;&nbsp;You may also contact us by phone at 1-866-503-3389, by email at&nbsp;<a href="mailto:ppsm2recall@WaltherArms.com" target="_self">ppsm2recall@WaltherArms.com</a>&nbsp;or by mail at Walther Arms, Inc., 7700 Chad Colley Boulevard, Fort Smith, AR&nbsp; 72916.The current time to repair your PPS M2 is approximately 4 to 6 weeks from the date we receive your PPS M2.We appreciate your assistance and apologize for any inconvenience this may cause you.&nbsp; Thank you for your patience and cooperation.THE INFORMATION BELOW IS THE REPLY THAT THE CUSTOMER RECEIVES FROM US VIA EMAIL AFTER THEY SUBMIT THEIR FORM:Thank you for submitting this information. A confirmation e-mail will be sent to the email address you provided.*Note: If you are shipping more than 1 x PPS M2 please complete the form once for each gun being returned to avoid any issues with processing.Please follow the guidelines noted below when preparing to return your PPS M2 pistol:1) Confirm that pistol is&nbsp;Unloaded 2) Do not ship ammunition with handgun3) Keep magazines at home4) Remove all aftermarket accessories5) Gun must be securely packaged and shipped in a FedEx Box in order to prevent damage during transit6) Retain the tracking information you were emailed for your package.<a href="https://waltherarms.com/wp-content/uploads/2020/04/PPS-M2-Recall-PressRelease.png" target="_self">CLICK HERE TO READ OFFICIAL WALTHER PPS M2 PRESS RELEASE</a> <h2>CCP RECALL (M1 9mm MODELS ONLY)</h2>*The Walther CCP M2 9mm and .380acp models are NOT affected by the Recall.&nbsp; If you have a CCP M2 in 9mm or .380acp you do not need to send it in for the upgrade.Important Safety Recall – MARCH 2017 Walther CCP PistolsWalther Arms has identified a potential condition in Walther CCP pistols that could potentially cause it to discharge if dropped whether the manual safety is engaged (on) or disengaged (off).&nbsp; The safety of our customers is our paramount concern, so we have voluntarily initiated this recall because of the possibility of a drop-fire occurring.Please do not load or fire your Walther CCP pistol and contact us immediately to arrange to have your pistol upgraded free of charge.If your pistol has already been upgraded, there will be a dot milled onto the back side of the magazine opening. &nbsp;The upgrade will be done at no charge to you.&nbsp; For free shipping, please enter your information&nbsp;<a href="https://waltherarms.wufoo.com/forms/ccp-recall-form/" target="_self">here</a>, and&nbsp;complete the online form, making sure to include the serial number. &nbsp;After completion of the form a confirmation email will be sent including shipping information.Please note:&nbsp; The serial number is located on the right side of the pistol (circled in red below)<a href="https://waltherarms.wufoo.com/forms/ccp-recall-form/" target="_self">PLEASE SUBMIT YOUR INFORMATION HERE – CCP RECALL</a>Please check this website and all safety notices on a regular basis for current information about your firearms.&nbsp; You may also contact us by phone at 1-866-503-3389, by email at&nbsp;<a href="mailto:ccprecall@WaltherArms.com" target="_self">ccprecall@WaltherArms.com</a>&nbsp;or by mail at Walther Arms, Inc., 7700 Chad Colley Boulevard, Fort Smith, AR&nbsp; 72916.The current time to repair your CCP is approximately 2 weeks from the time we receive it.We appreciate your assistance and apologize for any inconvenience this may cause you.&nbsp; Thank you for your patience and cooperation.&nbsp;<h2>PPK PPK/S RECALL</h2>Important Safety Recall – FEBRUARY 2013 PPK &amp; PPK/SSmith &amp; Wesson has identified a condition that may exist in certain PPK and PPK/S pistols which may permit a round to be discharged without the trigger being pulled. When the manual safety is disengaged, Smith &amp; Wesson’s Product Engineering Group has determined that the possibility exists in certain firearms that lowering the hammer may cause a chambered round to fire.This recall applies to all Walther PPK and PPK/S pistols manufactured by Smith &amp; Wesson from March 21, 2002, until February 3, 2009. The Serial Numbers of the pistol subject to this recall are as follows:0010BAB – 9999BAB0000BAC – 9999BAC0000BAD – 9999BAD0000BAE – 9999BAE0000BAF – 9999BAF0000BAH – 9999BAH0000BAJ – 9999BAJ0000BAK – 9999BAK0000BAL – 5313BAL0000BAM – 1320BAM0000LTD – 0499LTD0001PPK – 1500PPK0026REP – 0219REP0001WLE – 0459WLESTOP USING YOUR PISTOL&nbsp;AND RETURN IT AT ONCE. Any unintended discharge of a firearm has the potential for causing injury and we ask that you stop using your pistol immediately. To facilitate the repair of your pistol please contact customer service to receive instructions. Upon receipt of your pistol, we will replace the existing hammer block with a new part at no cost to you. Your firearm will be returned as quickly and efficiently as possible.When your pistol is returned, you should note a punch dot which appears at the back of the frame. See the photograph below. This marking is verification that the new hammer block has been installed and that your pistol is safe to handle.Please contact Walther Arms via phone (479) 242-8500 or email us using the&nbsp;<a href="https://www.waltherarms.com/2015/contact-us/" target="_self">Contact Us form</a>&nbsp;if your PPK or PPK/S serial number is within the range of recalled guns. Our customer service team will provide you with an RA#, Return Form, and a Prepaid FedEx label.&nbsp;<h2>PK380 RECALL</h2>Important Safety Recall – OCTOBER 2012 Walther PK380 PistolsWalther has identified a condition that may exist in certain PK380 pistols which may permit a round to be discharged if the trigger is pulled, despite engagement of the manual safety. Walther has found that engagement of the manual safety may not prevent firing of a chambered round when the trigger is pulled.This recall applies to Walther PK380, .380 ACP pistols manufactured by Carl Walther GmbH from May 2012 to September 2012, and which have a Serial Number ranging from&nbsp;PK101201 to PK112155**NOTE:&nbsp; If the serial number begins with WB, it is NOT involved in the recall.&nbsp;STOP USING YOUR PISTOL, and UNLOAD IT IMMEDIATELY, exercising EXTREME CARE in doing so AND RETURN IT TO WALTHER ARMS, INC. AT ONCE. Any unintended discharge of a firearm has the potential for causing injury or even death, and we ask that you stop using your pistol immediately. When unloading your pistol, please take extreme care to ensure that your firearm is pointed in a safe direction.Your pistol will be repaired at no cost to you. Your firearm will be returned as quickly and efficiently as possible.&nbsp;All shipping and repair costs will be covered by Walther Arms, Inc.<h4>NOTE: IF YOU HAVE A PK380 GUN THAT MEETS THE ISSUES MENTIONED ABOVE, PLEASE CONTACT US BY PHONE (479) 242-8500 OR&nbsp;<a href="https://www.waltherarms.com/customer-support/" target="_self">BY EMAIL</a>&nbsp;AND WE’LL EVALUATE THE RETURN WITH YOU.</h4>

PPS M2 RECALL (M2 MODELS ONLY)

<h5>Product Under Safety Recall Notice</h5>Smith &amp; Wesson's i-Bolt rifle<h5>Description of the Hazard</h5>Smith &amp; Wesson has discovered that the sear engagement pin in certain i-Bolt action rifles does not meet specification.&nbsp; The sear engagement pin is part of the fire control unit for the rifle which is manufactured for Smith &amp; Wesson by an outside vendor.&nbsp; Our investigation has revealed that some of the sear engagement pins produced for Smith &amp; Wesson do not comply with specifications and may, in certain instances, lead to a failure of this component.&nbsp; Although we have not received any reports of accidents or injuries, we are initiating this recall campaign in the interest of safety since a failure of the sear engagement pin may potentially lead to an unintended discharge of your rifle.&nbsp;You should stop using the rifle immediately and return it to Smith &amp; Wesson so that the appropriate corrective action can be taken.&nbsp;<h5>Description of the Product Involved</h5>This recall applies only to i-Bolt rifles manufactured by Smith &amp; Wesson between October 18, 2007 and December 12, 2007.&nbsp; The recall is limited to 597 rifles produced during this time period.&nbsp;&nbsp;<a href="https://assets.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt23f8467ef8f6ff69/63d3f8f535e4be151745a9fa/IBolt_serial_numbers.pdf" target="_self">Click this link to view the list of serial numbers for all rifles affected by this recall</a>To determine if your rifle is part of this recall, please check your serial number which can be found near the forward end of the scope mount base as indicated below:<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt8e5441ef0a19369a/638e59ab88a059043027e6f9/iBolt_Serial_number.jpg" alt="Serial number near the forward end of the scope mount base" /></figure>If your serial number does not appear on the list, you do not need to return your rifle.<h5>Action to be Taken</h5>When your rifle is returned to Smith &amp; Wesson, we will inspect each sear engagement pin to verify that it meets specification.&nbsp; If the pin fails to meet specification, a new one will be provided and installed for you free of charge.&nbsp; Your rifle will be returned to you once we verify that the fire control unit functions properly.<h5>Consumer Contact</h5>Please contact Smith &amp; Wesson directly at 1-800-331-0852 to arrange for the return of your rifle.&nbsp; All work will be done free of charge.

I-BOLT RIFLE SEAR ENGAGEMENT PIN SAFETY RECALL

<h5>Product Under Safety Recall Notice</h5>Model 22A Pistols<h5>Description of the Hazard</h5>Smith &amp; Wesson has identified a condition that may exist in certain model 22-A pistols. Based on our ongoing product review, we have determined that the slides of certain pistols manufactured from August 1, 2008 to February 19, 2009, may not meet the design specification. This can create a situation where insufficient headspace exists creating a risk of unintended discharge.<h5>Description of the Product Involved</h5>This recall applies only to 22-A pistols manufactured from August 1, 2008 to February 19, 2009. Affected pistols fall within the following serial number range: UBW0000 - UBW9999 UBY0000 - UBY4104<h5>Action to be Taken</h5>STOP USING YOUR PISTOL&nbsp;AND RETURN IT TO SMITH &amp; WESSON AT ONCE.&nbsp;Any unintended discharge of a firearm has the potential for causing injury, and we ask that you stop using your pistol immediately.Please contact Smith &amp; Wesson's customer service department for instructions on the return on your pistol.&nbsp;Verification of Corrective ActionWhen your pistol is returned, you should note a punch dot which appears on the rear underside of the slide. This punch dot can be seen by locking the slide to the rear and looking at the underside of the slide as seen in the photograph below.<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt9d7f4972a0b86139/638e5ae23a0e946001a47a1c/M22A_SLIDE_MARKED1.jpg" alt=" Punch dot on the rear underside of the slide" /></figure>This punch dot is verification that your slide meets specification, and the pistol is safe to use. If your pistol already has this punch dot, you do not need to return the firearm.<h5>Consumer Contact</h5>To receive a FedEx pre-paid billable stamp and shipping instructions to arrange for the modification of your pistol email us at&nbsp;<a href="mailto:22A@smith-wesson.com" target="_self">22A@smith-wesson.com</a>&nbsp;or call us at 1-800-331-0852. Please allow 2-3 weeks to receive the information packet from us.

MODEL 22A PISTOLS SAFETY RECALL

<h5>Product Under Safety Recall Notice</h5>ALL&nbsp;Thompson/Center Arms ICON®, VENTURE® and DIMENSION™ rifles manufactured before June 13, 2013.<h5>Description of the Hazard</h5>Thompson/Center Arms has identified a condition where the safety lever in certain rifles may bind preventing the safety from becoming fully engaged. In this situation, closing the bolt may move the safety to the fire position. The rifle will not fire unless the trigger is pulled. However, out of an abundance of caution, we are initiating this recall to allow for the prompt inspection and, if necessary, the repair of each rifle.<h5>Description of the Product Involved</h5>This recall applies to all ICON, VENTURE and DIMENSION rifles manufactured before June 13, 2013. The following is a list of affected models:<table><tbody><tr><td>&nbsp;Icon</td><td>&nbsp;Venture</td><td>&nbsp;Dimension</td></tr><tr><td>&nbsp;Icon Classic</td><td>&nbsp;Venture Predator</td><td>&nbsp;</td></tr><tr><td>&nbsp;Icon Weather Shield</td><td>&nbsp;Venture Infinity</td><td>&nbsp;</td></tr><tr><td>&nbsp;Icon Precision Hunter</td><td>&nbsp;Venture Dream Season</td><td>&nbsp;</td></tr><tr><td>&nbsp;Icon Warlord</td><td>&nbsp;Venture Weather Shield</td><td>&nbsp;</td></tr><tr><td>&nbsp;Icon Field</td><td>&nbsp;Venture Compact</td></tr></tbody></table><h5>Remedy/Action to be Taken</h5>STOP USING YOUR RIFLE.To remedy this condition, your rifle will be inspected and if necessary repaired at no cost to you. Your firearm will be returned as quickly and efficiently as possible. All shipping and repair costs will be covered by Thompson/Center Arms.Even in the recall condition, the rifle will not fire unless the trigger is pulled. Therefore, always follow these basic firearm safety rules:<ul><li>Keep your chamber unloaded until you are ready to shoot.</li><li>Always keep your firearm pointed in a safe direction.</li><li>Never place your finger on the trigger until you have made a conscious decision to fire your rifle.</li></ul>Outside the United States,&nbsp;<a href="https://www.smith-wesson.com/customer-service/warranty-stations" target="_self">CLICK HERE</a>&nbsp;for a list of Authorized Warranty Centers that will repair your rifle.Verification of Corrective ActionWhen your rifle is returned, you should note a punch dot on the safety lever.&nbsp; See the photograph below.&nbsp; This punch dot is confirmation that your rifle has been inspected and the hazard has not been found or has been corrected.<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt8439fe7841447d0f/638e5d07b477ba0429bf0c2e/TC_Recall_June2013_Photo1_497.jpg" alt="Punch dot on back of revolver" /></figure><figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt452cb56239b1c21a/638e5d260c244067292a3e18/TC_LabelStamp_Callout_June2013.jpg" alt=" A red star on a label" /></figure>When you rifle is returned, you should also note a red star on the label on the outside of your box. &nbsp;See the photograph above. &nbsp;This mark is further confirmation that your rifle has been inspected and the hazard has not been found or has been corrected.&nbsp;<h5>Consumer Contact</h5>To receive a FedEx pre-paid label and shipping instructions please call 877-318-0644. &nbsp;

ALL THOMPSON/CENTER ARMS ICON®, VENTURE® AND DIMENSION® RIFLES MANUFACTURED BEFORE JUNE 13, 2013.

<h5>Product Under Safety Recall Notice</h5>Smith &amp; Wesson's Performance Center Model 460 Revolvers&nbsp;<h5>Description of the Hazard</h5>Smith &amp; Wesson has received four (4) reports of barrel failures involving its Performance Center Model 460 revolvers. &nbsp;These barrels were manufactured by an outside supplier. &nbsp;Our investigation has revealed that the quality of steel in some of these barrels did not meet the performance requirements for these firearms and may have contributed to failure of the barrel.&nbsp;You should stop using the revolver and return it immediately to Smith &amp; Wesson so that your barrel can be inspected and replaced, if necessary.&nbsp;<h5>Description of the Product Involved</h5>This recall applies to Performance Center Model 460 revolvers shipped by the&nbsp;Smith &amp; WessonPerformance&nbsp;Center&nbsp;prior to&nbsp;September 18, 2006.&nbsp; This recall does NOT apply to Smith &amp; Wesson standard production Model 460 revolvers.&nbsp; The affected revolvers can be identified by the following Serial Number Range:EBD0001 - EBD0524EBF0002 - EBF0251LHZ0000 - LHZ0511LLL0000 - LLL0702LRR0001 - LRR0552MMM0001 - MMM1809XMC0001 - XMC0109To determine if your firearm is part of this recall, please check your serial number which can be found on the yoke of your firearm as indicated below.&nbsp; Each Performance Center Model 460 will have the words "Performance&nbsp;Center" engraved on the barrel as indicated below:<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt84f31720446e3d09/638e5b8ba1a0cf5e10d8e8c6/image001_(1).gif" alt="Performance Center engraved on the barrel of the gun" /></figure><h5>Action to be Taken</h5>When the revolver is returned to Smith &amp; Wesson, we will inspect and test each barrel to verify that it meets specification.&nbsp; If the barrel fails to meet specification, a new one will be provided and installed for you free of charge.&nbsp;We have already begun the corrective action process on Performance Center Model 460 revolvers.&nbsp; To determine whether your revolver has been inspected, please do the following:<ol><li>Keep the firearm pointed in a safe direction;</li><li>Open the cylinder and verify that the firearm is unloaded; and</li><li>Look for a "punch dot" in the yoke opening, just above the serial number, as shown below. &nbsp;If this indicator is present, your revolver has already been inspected and no further action is required.&nbsp;</li></ol><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt59f9d0a18d03e0f8/638e5bac53094605f9b83c98/image003_(1).gif"/><h5>Consumer Contact</h5>Please contact Smith &amp; Wesson directly at 1-800-331-0852 ext. 2905, or email us at&nbsp;<a href="mailto:qa@smith-wesson.com" target="_self">qa@smith-wesson.com</a>&nbsp;to arrange for the return of your revolver.&nbsp; All work will be done free of charge.

PERFORMANCE CENTER MODEL 460 SAFETY RECALL

IMPORTANT SAFETY RECALL NOTICE February 20, 2009PRODUCT:&nbsp;Walther PPK and PPK/S pistolsDESCRIPTION OF THE HAZARD:&nbsp;Smith &amp; Wesson has identified a condition that may exist in certain PPK and PPK/S pistols which may permit a round to be discharged without the trigger being pulled. When the manual safety is disengaged, Smith &amp; Wesson’s Product Engineering Group has determined that the possibility exists in certain firearms that lowering the hammer may cause a chambered round to fire. This recall applies to all Walther PPK and PPK/S pistols manufactured by Smith &amp; Wesson from March 21, 2002, until February 3, 2009.&nbsp; The Serial Numbers of the pistols subject to this recall are as follows: DESCRIPTION OF THE PRODUCT INVOLVED: 0010BAB - 9999BAB 0000BAC - 9999BAC 0000BAD - 9999BAD 0000BAE - 9999BAE 0000BAF - 9999BAF 0000BAH - 9999BAH 0000BAJ - 9999BAJ 0000BAK - 9999BAK 0000BAL - 5313BAL 0000BAM - 1320BAM 0000LTD - 0499LTD 0001PPK - 1500PPK 0026REP - 0219REP 0001WLE - 0459WLE REMEDY/ACTION TO BE TAKEN: STOP USING YOUR&nbsp;PISTOL AND RETURN IT TO SMITH &amp; WESSON AT ONCE. Any unintended discharge of a firearm has the potential for causing injury, and we ask that you stop using your pistol immediately. To facilitate the repair of your pistol, please complete the Safety Recall Form or contact Smith &amp; Wesson's customer service department at 855-774-8527&nbsp;to receive instructions for the return of your pistol to Smith &amp; Wesson. When you return your pistol to Smith &amp; Wesson, we will replace the existing hammer block feature with a new part at no cost to you. Your firearm will be returned as quickly and efficiently as possible. VERIFICATION OF CORRECTIVE ACTION: When your pistol is returned, you should note a punch dot which appears at the back of the frame. See the photograph below.&nbsp;&nbsp; <figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt041149822f27857b/638e1ba42e4a1f63daca9246/ppk.png" alt="A punch dot at the back of the frame" /></figure>This marking is verification that the new hammer block has been installed and that your pistol is safe to handle. CONSUMER CONTACT:&nbsp;To receive a FedEx pre-paid label and shipping instructions please call 855-774-8527. IF YOU HAVE ANY QUESTIONS ABOUT THIS RECALL, PLEASE CONTACT SMITH &amp; WESSON AT 855-774-8527 &nbsp;

PPK SAFETY RECALL

M&amp;P SHIELD® EZ® PISTOL IMPORTANT SAFETY RECALL NOTICE FOR PISTOLS MANUFACTURED BETWEEN MARCH 1ST, 2020 AND OCTOBER 31ST, 2020Smith &amp; Wesson has identified two M&amp;P Shield EZ Pistols on which the hammers manufactured by our supplier were cracked.&nbsp; In those firearms, the hammer failed to fully engage the sear, causing the round to fire, cycling the slide, and potentially resulting in multiple discharges without depressing the trigger.&nbsp; This issue can occur in the following two scenarios:<ol><li>With a loaded magazine in the firearm and the grip safety depressed, releasing the slide (by pulling it back, or releasing the slide stop), may ignite the round as the slide closes, without engaging the trigger.&nbsp; The condition may occur, regardless of the manual thumb safety position if equipped.&nbsp; This may also result in multiple discharges.</li><li>With a loaded magazine in the firearm, the grip safety depressed, manual safety in the fire position, slide closed, and a round in the chamber, pulling the trigger will cause the round to fire normally, however as the slide cycles, the next round may be ignited as it is chambered by the hammer failing to fully engage the sear, causing multiple discharges.</li></ol>In all cases, the firearm will NOT fire unless the grip safety is depressed.&nbsp; While this condition has been found only in two hammers, and our investigation suggests that these two incidents are very isolated, any unintended discharge of a firearm has the potential to cause injury.&nbsp; Therefore, we have established this Safety Recall as a precautionary measure&nbsp;to ensure that all M&amp;P Shield EZ Pistols in service meet our design specifications.&nbsp;Stop using your M&amp;P® Shield™ EZ pistol until you determine whether it is included in this safety recall, and if so, until it has been inspected and repaired by Smith &amp; Wesson, if necessary.PRODUCT AFFECTED:This notice applies ONLY to M&amp;P® Shield™ EZ pistols (including Performance Center® models) manufactured between March 1, 2020 and October 31, 2020, and only to a small percentage of that population. It does NOT apply to all SHIELD™ pistols.&nbsp; To determine whether your M&amp;P Shield EZ Pistol is affected, check the label on the box to determine date of manufacture (see image below), and if manufacture date is between March 1, 2020 and October 31, 2020 – your pistol may be affected. In this case (or if you are unsure of your date of manufacture), simply go to MPShieldEZrecall.com and input your serial number, or call 888-871-7114 .FOR OWNERS OUTSIDE THE UNITED STATES:For M&amp;P Shield EZ Pistol owners outside the United States, see our list of Authorized Warranty Centers available at&nbsp;<a href="https://www.smith-wesson.com/customer-service/warranty-stations" target="_self">smith-wesson.com/customer-service/warranty-stations</a>, who will inspect your pistol and replace your hammer as necessary.FOR DEALERS/DISTRIBUTORS/RETAILERS:<ol><li>If you have less than 5 affected firearms, please input your serial numbers to receive return labels. If you have 5 or more&nbsp;affected pistols in inventory, please call&nbsp;888-871-7114&nbsp;and we will coordinate a pickup of the affected firearms. In either case, the firearms will be expedited to our facility, repaired, and returned to you ASAP.</li><li>For those pistols on the list which you have already sold, we ask that you provide us with the names, addresses, telephone numbers and e-mails of customers to whom you have sold them to. &nbsp;Please send this information to us electronically at&nbsp;</li></ol>REMEDY/ACTION TO BE TAKEN:If your M&amp;P Shield EZ Pistol is included in this recall, we will arrange for the return of your firearm to Smith &amp; Wesson for inspection.&nbsp; After inspection, if the hammer from your firearm is affected, it will be replaced at no cost to you.&nbsp; We expect that this entire process will take no longer than 10 business days, and your pistol will be returned as quickly and efficiently as possible.&nbsp; All shipping and replacement costs will be covered by Smith &amp; Wesson.HOW TO LOCATE YOUR SERIAL NUMBER AND DATE OF MANUFACTURE:<figure style = "float: none;width: auto;max-width:auto;"><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltc4a4306bc0b35974/638e56fc8d70f761c6b2ee10/serial_number_location.webp" alt="Serial Number and Manufacture" /></figure>NOT ALL M&amp;P SHIELD EZ PISTOLS MANUFACTURED BETWEEN MARCH 1, 2020 AND OCTOBER 31, 2020 ARE INCLUDED IN THIS RECALL.If your pistol was manufactured between these dates, please enter the serial number inscribed on your pistol&nbsp;in the field below&nbsp;to determine&nbsp;if it is included in this recall.&nbsp; You may enter multiple serial numbers.&nbsp; After you have checked all of your serial numbers, you will be asked to complete a pre-paid return label request&nbsp;form.&nbsp;

M&P® SHIELD™ EZ™ RECALL NOTICE FOR PISTOLS

Smith & Wesson is committed to producing firearms of the highest quality. To accomplish this goal, we are constantly evaluating and monitoring the safety, reliability and performance of our products. As part of this ongoing evaluation process, we have received reports, in an extremely small number of cases, that the firing pin safety plunger of the SW1911 pistol can become disabled, creating a situation where the slide may jam and render the firearm inoperable. This only pertains to certain Smith & Wesson Model SW1911 pistols bearing serial numbers JRD0000 to JRD4750.
To date, none of these cases have resulted in any injury, and Smith & Wesson has not received any reports of any accidental discharge associated with the functioning of the firing pin safety plunger. While the company has not received any reports of injury, a failure of the firing pin safety plunger may affect the reliability and safety of your firearm. Therefore, given our commitment to quality and safety, we are initiating this recall campaign, and we are offering to repair, free of charge, any affected SW1911 pistol.
For more information please view the "SW1911 Safety Recall Notice" PDF file at the top of this page. If after viewing the document you believe your SW1911 requires service, please call us at&nbsp;1-800-331-0852&nbsp;or email us at&nbsp;<a href="mailto:qa@smith-wesson.com" target="_self">qa@smith-wesson.com</a>. A special FedEx return label and shipping instructions to facilitate the return of your Model SW1911 Pistol will be mailed to you promptly. If you have any questions you may call&nbsp;1-800-331-0852&nbsp;for more information.
Download:
<a href="https://assets.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltdb45cf4ec6c1c672/63d3f5dc3d28dd4dde641d69/SW1911_Recall.pdf" target="_self">https://www.smith-wesson.com/sites/default/files/recalls/SW1911_Recall.pdf</a>

SW1911 SAFETY RECALL

The specific recall information can be found here on the Walther Arms website: <a href="https://waltherarms.com/recall" target="_self">https://waltherarms.com/recall</a>

Walther PK380 Recall

Like any firearm, the function of the M&P®380 Shield™ EZ™ Manual Thumb Safety pistol can be influenced by the type and quality of ammunition used with the pistol. &nbsp;In the case of the M&P 380 Shield EZ Manual Thumb Safety, we have found that in very rare circumstances, ammunition that produces a high level of felt recoil can cause the manual safety to move from the fire to the “safety on” position during firing. &nbsp;Should this occur, you will not be able to fire the next round unless and until the manual safety is reset to the fire position.At Smith & Wesson, we are committed to designing and producing firearms that meet the highest quality and performance standards. &nbsp;To ensure that every Smith & Wesson handgun meets our standards for reliability and performance, as of April 4, 2018, we have engineered the manual safety so that it will be less susceptible to the influence of ammunition weight, velocity and loads. &nbsp;Any M&P 380 Shield EZ Manual Thumb Safety pistol produced before April 4, is eligible for a no-cost upgrade.&nbsp; To determine if this consumer advisory applies to your pistol, please utilize our serial number verification tool. If your pistol is subject to this advisory, please call Smith & Wesson at 1-800-331-0852 or email us at&nbsp;<a href="mailto:MP380EZAdvisory@Smith-Wesson.com" target="_self">MP380EZAdvisory@Smith-Wesson.com</a>. &nbsp;A FedEx return label and shipping instructions to facilitate the return of your M&P 380 Shield EZ pistol will be mailed to you promptly. &nbsp;If you have any questions, you may call 1-800-331-0852 for more information. WARNING: READ AND FOLLOW THE WARNINGS IN YOUR OWNER’S MANUAL. &nbsp;NEVER USE “PLUS-P” (+P), “PLUS-P-PLUS” (+P+); OR RELOADED AMMUNITION WITH THE M&P 380 EZ. &nbsp;ALWAYS USE FACTORY MANUFACTURED AMMUNITION PRODUCED TO SAAMI SPECIFICATIONS.

M&P®380 SHIELD™ EZ™ CONSUMER ADVISORY

<h5>Product Under Safety Recall Notice</h5>ALL&nbsp;Thompson Center Venture Rifles manufactured prior to October 28, 2011.<h5>Description of the Hazard</h5>During an internal technical review, Smith & Wesson identified a condition that may exist with the sear supplied with some rifles that would allow the rifle to fire without the trigger being pulled.&nbsp; In the interest of consumer safety, we are initiating this recall to allow for the prompt inspection and, if necessary, the repair of each rifle.<h5>Description of the Product Involved</h5>This broadens the recall announced by Smith & Wesson on November 8, 2011.&nbsp; This recall applies to&nbsp;ALL&nbsp;Venture rifles manufactured prior to October 28, 2011.&nbsp; To determine if your rifle is affected, please reference the serial number list located at the link below.&nbsp; If your serial number does not fall within the list of affected serial numbers, your rifle is not part of this recall.<h5><a href="https://assets.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltdb61ede0299b5568/63d15ab304ee8615186bc56f/Venture_Recall_Serials.pdf" target="_blank">Click Here For List of Recalled Serial Numbers</a></h5><h5>Remedy/Action to be Taken</h5>STOP USING YOUR RIFLE.Any unintended discharge of a firearm has the potential to cause injury or death, and we ask that you stop using your rifle until we have an opportunity to inspect the sear to make certain that there is no condition which will allow the rifle to fire without the trigger being pulled.To facilitate the inspection and, if necessary, repair of your rifle, please contact Smith & Wesson’s customer service department to receive instructions and a prepaid return label for the return of your rifle to Smith & Wesson.Outside the United States,&nbsp;<a href="/customer-service/warranty-stations" target="_self">click here</a>&nbsp;for a list of Authorized Warranty Centers that will repair your rifle.When you return your rifle to Smith & Wesson, be sure to attach the completed information card received from Smith & Wesson, so that your rifle can be returned to you as quickly and efficiently as possible.&nbsp;Verification of Corrective ActionWhen your rifle sear is returned, you should note a punch dot on the trigger assembly.&nbsp; See the photograph below.&nbsp; This punch dot is confirmation that your sear has been inspected and the hazard has not been found or has been corrected.<img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/blt5c4b65c4af89ad8d/638e5d7fa8ba0e5eb857df29/venturerecallimage.jpg" height="auto" width="572" max-width="572"/><img src="https://images.contentstack.io/v3/assets/bltb61dcb3c40854cd9/bltf635ad752f3292d5/638e5d92bc3535195feb1833/venturerecallimage1.jpg" height="auto" width="595" max-width="595"/>When your rifle sear is returned, you should also note a red checkmark on the label on the outside of your box. See the photograph above. &nbsp;This checkmark is further confirmation that you sear has been inspected and the hazard has not been found or has been corrected.&nbsp;<h5>Consumer Contact</h5>To receive a FedEx pre-paid label and shipping instructions to arrange for the modification of your Venture Rifle email us at&nbsp;<a href="mailto:venturerecall@smith-wesson.com" target="_self">venturerecall@smith-wesson.com</a>&nbsp;or call us at 1-800-331-0852 to arrange for the inspection and repair, if necessary, of your rifle.Outside the United States,&nbsp;<a href="/customer-service/warranty-stations" target="_self">click here</a>&nbsp;for a list of Authorized Warranty Centers that will repair your rifle. For reimbursement of shipping charges to an Authorized Warranty Center for the modification of your Venture Rifle, please send a request to&nbsp;<a href="mailto:venturerecall@smith-wesson.com" target="_self">venturerecall@smith-wesson.com</a>