|How do I adjust the Laser on my BODYGUARD®38 revolver?|
WARNING: ENSURE YOUR FIREARM IS UNLOADED BEFORE ADJUSTING YOUR SIGHT. AT ALL TIMES FOLLOW THE BASIC FIREARMS SAFETY RULES IN THE SECTION ENTITLED "YOUR SAFETY RESPONSIBILITIES" OF YOUR BODYGUARD® 38 SAFETY AND INSTRUCTION MANUAL.
WARNING: VISIBLE LASER RADIATION EMITS FROM THE INSIGHT® LASER WHILE IT IS IN OPERATION - AVOID DIRECT EYE EXPOSURE.
1. Turn the elevation adjustment screw (on top of the laser) four (4) complete rotations counter-clockwise with the allen wrench provided with your BODYGUARD® 38 revolver.
2. Turn the windage adjustment screw (on the side of the laser) four (4) complete rotations counter-clockwise with the allen wrench provided with your BODYGUARD® 38 revolver.
3. Pick a suitable aiming point where you can see the fixed sight picture and the laser beam at the same time. The point should be 8 to 10 feet from the BODYGUARD® 38 revolver.
4. Turn the elevation adjustment screw so that the beam is two inches (2") above point of impact as referenced from the fixed sight picture. (Note: the beam will move approximately one inch (1") left of point of impact.)
5. Turn the windage adjustment screw so that the beam is to the point of impact as referenced from the fixed sight picture.
6. Turn the elevation adjustment screw so that the beam is to the point of impact as referenced from the fixed sight picture.
7. Test fire the BODYGUARD® 38 revolver with your particular type and brand of ammunition and make any final adjustments necessary, making sure the revolver is unloaded prior to making any adjustments to the laser sight.
Click Here For Downloadable Instructions
|What kind of ammunition should I use in my S&W handgun?|
|Use only commercially manufactured ammunition with internal ballistic pressures which are in strict accordance with the specifications of the Sporting Arms and Ammunition Manufacturers' Institute (SAAMI).|
Be certain all ammunition you use complies with the SAAMI specifications. If you are uncertain, contact your ammunition supplier for verification.
If you would like any further information on specific ammunition, you may contact one of the major ammunition manufacturers from the link listed below:
|Can I dry fire my S&W handgun?|
|Q: Can I dry fire my Smith & Wesson?|
A: Yes, except for the .22 caliber pistols which includes models 22A, 22S, 422, 2206, 2214, 2213 and 41.
.22 caliber revolvers such as models 17, 43, 63, 317 and 617 also should not be dry fired.
Q: Why can't I dry fire my .22 pistol or revolver?
A: Dry firing a S&W .22 pistol or revolver will cause damage to the firing pin.
|Does Smith & Wesson offer gunsmithing services?|
|The Smith & Wesson Performance Center offers a full line of gunsmithing services.
Smith & Wesson Performance Center Gunsmithing Services
|How can I request the history of my S&W handgun?|
|Weapon History Request|
|Where can I find S&W holsters?|
|Smith & Wesson offers a wide variety of Holsters in the Firearm Accessories section in our Online Store.|
|What is the warranty on S&W knives?|
|Limited Lifetime Warranty: The product is warranted to the original consumer purchaser, for as long as he or she lives, against defects in materials, manufacture of assembly. Damage due to abuse, misuse or neglect is not covered. Defective products will be repaired or replaced. Discontinued items that are not repairable will be exchanged for items of equal value. In order to get service under this warranty, send the product prepaid, together with an explanation of the defect to the address listed below. Please add $6.95 for return freight. It is recommended that you insure the defective products to be returned.|
Smith & Wesson Knives will not be responsible for any damages for loss or use of defective products or for other consequential or incidental damages.
Taylor Brands, LLC
1043 Fordtown Road
Kingsport, TN 37663
|Where is the serial number located on my handgun?|
|Revolvers - The official serial number is located on the bottom of the butt of the frame. Some revolvers also have the serial number located on the inside of the frame, in the yoke area. |
Pistols - The serial number is located on the side of the frame.
Sigma series - The serial number is located on the frame under the front of the handgun.
SW99 - The serial number is located on the frame at the rear of the pistol.
|Where can I find S&W long gun parts & service?|
|For long guns manufactured in the early 1980's, please contact the following dealers for parts and service. Smith & Wesson discontinued these models and no longer has a parts inventory or offer repair service for these models.|
W. Hurley, NY 12491
10059 Hwy 1476
Comanche, TX 76442
For Model 1020, 1012 or Elite Shotguns, please contact our Customer Service Department for parts or service at 800-331-0852.
|How can I obtain a manual for my S&W handgun or an S&W catalog?|
|Where can I find information on Performance Center handguns?|
|Smith & Wesson Performance Center Handguns|
|Where can I find pricing information on S&W Handguns?|
|Pricing information is included on most of our firearm detail pages on our website|
You may also contact one of our customer support representatives for pricing on handguns.
1-800-331-0852 Ext. 2904 8:00 a.m. to 8:00 p.m. Eastern Standard Time, Monday - Friday.
|Where can I purchase S&W gifts and apparel?|
|Click on "The Store" link located at the top right of every page on the website|
|Where can I purchase S&W handgun parts and accessories?|
|Smith & Wesson Online Store - Firearm Accessories|
|How can I get my S&W handgun repaired?|
|Please use our Warranty Repair Shipping Form to enter your information to receive a prepaid Fedex return label to return your S&W handgun for repair. Customers outside the USA may contact the International Warranty Service Center nearest you.|
|Where can I get my S&W pellet or air gun repaired?|
|Smith & Wesson discontinued manufacturing air and pellet guns in 1980. The air and pellet gun line included the models: 77A, 78G, 79G and 80G. Should your Smith & Wesson air gun require parts and/or repairs, please contact:|
Bimrose Precision Airgun Repair is now located at:
13090 Navajo Road #3
Apple Valley, CA 92308
TMac's Airgun Service
C/O Tony McDaniel
1120 Finger Bridge Road
Hickory NC 28602
|Models 586 and 686 pellet guns, please contact:|
|Umarex USA, Inc.
6007 S 29th Street
Fort Smith, AR 72908
|We suggest that you call before shipping your air gun to ensure they have the required parts.|
|How can I find out the value of my S&W handgun?|
|Unfortunately, we are unable to predict the value of handguns after they are shipped from the factory. You may wish to reference one of the many books written on the value of handguns at your local bookstore or library.|
If you would like to obtain the history of your Smith & Wesson handgun please refer to the Request History of your S&W Handgun question above.
|Where can I find an S&W Warranty Service Center?|
|S&W Warranty Service Centers|
|What is the history of S&W?|
|Read the history of Smith & Wesson|
|Where can I find shipping and return information?|
|Shipping & Returns|